Use search function please. All the info found with Ł - refers to this site

This Article Content

Rights Reserved - Free Access.
This digital object is protected by copyright and/or related rights. This digital object is accessible without charge, but its use is subject to written permission.
Unless expressly stated otherwise in the licensing conditions, you are free to make any of the acts permitted by your national copyright and related rights act, including browsing, printing and making a copy for your own personal purposes.
All other acts of reproduction and communication to the public are subject to the licensing conditions attached to the digital object.


Black U.S. "Jungle" Boots, Speed-Laces, "Panama"-type out-soles

The "jungle" boots of the Vietnam era proved to be very successful and the increasing use of these boots as a general-purpose combat boot brought some changes.

Since "jungle" boots were introduced in the early 1960s and used widely by the American troops in Vietnam, these boots have gone through only minor design changes and some improvements. Some novelties were accepted, some of them were discarded, but most of modifications were proposed for the reasons of cost and convenience to the contractor.

For example, the artificial rubber out-sole composition was changed to avoid marking linoleum floors at stateside military bases. The removable ventilating "SARAN®" insoles were changed for waterproof "Poron®" linings, but this idea can hardly be considered as any improvement, because water still entered the "jungle" boots via the drain eyelets, and soaked the open-cell "Poron®" insoles which remained in constant contact with the bottom of the foot. Some countries, in contrast, still continue to use the removable ventilating "SARAN®" insoles primarily because of their good insulating properties.

In the 1980s some of the issue boot's the "Panama®"-type out-soles were reverted to the "Vibram®"-type out-soles. The "Vibram®"-type out-soles were more suitable to use on rocks, sand, or other hard terrain, but lacked the mud-clearing features of the "Panama®"-type out-soles, and were inferior for use in swampy or jungle environments.

Some changes were made to lower acquisition costs, which sometimes led to quality of materials decreasing. At the end of 1980s, some incidents of heel blowouts and loss of screened water drain eyelets due to lack of quality control and use of poor materials were reported.

Anyway, for decades following the Vietnam war, the "jungle" boots has become the standard combat footwear for mild weather.

An interesting fact: the American G.I.'s use to have two "dog tags" (identification steel plates with personal information). During combat operations, one of these "dog tags" use to be tied to the soldier's boot lacing. This should increase the probability of successful personality identification of the G.I.'s body even after heavy wounds.

The last nomenclature for the "jungle" boots was "Boot, Hot Weather, Type I, Black, Hot-Wet" and allowed for both OG107 green and black for the nylon sections of the upper. In addition, the Type II boot was defined, identical except with desert tan color for the leather and the nylon.

Black nylon was added to the spec with revision of military specification MIL-B-43154K (Amendment 1) of September 15, 1989. Speed Lace Assembly also added in later specs, and a Tan desert version as well.

Black Speed Lace "jungle" boots came with the following "Lacing Instructions for Speed Laces":

Step 1. After first lacing through all loops and tying each end of the lace with a hard knot, loosen up lace for easy step-in of foot.

Step 2. With thumbs on either edge remove all pleats and wrinkles by pushing tongue securely around leg.

Step 3. Hold lace ends at pre-tied knots. Pull up lace to desired tightness.

Step 4. Wrap extra-lace length around collar and secure.

The last revision of military specification for these boots is MIL-B-43154M of June 26, 1992, which was canceled on May 15, 1999, described these boots in the following way:

"The fore-foot part of the upper is leather as is the area along the closure system. The rest of the upper is nylon Cordura®. The entire upper on this boot is unlined. Two screened eyelets are set in the upper leather in the medial side of the boot in the waist area to facilitate air circulation and water drainage (Figure 2).

Figure 2

Nylon tape (1 inch) is on the back of the boot (backstrap area) and around the collar. A nylon tape (2 inch) also runs diagonally across the ankle (Figure 3).

Exclusively for

mobile version of the page

We have much more interesting information on this site.
Click MENU to check it out!© 2013-2019 mailto: